Seal ‘n Lock Ultra Wet Look® Concrete Paver Water-Based Sealer
- ULTRA-WET-LOOK® – Is user friendly and environmentally safe. The high solids content of pure urethane wears evenly and lasts longer than solvent based paver sealers.
- FINISH EVERYTHING ALL IN ONE DAY – No need to wait for your pavers to dry before using this water based concrete sealer. You can apply the sealer on concrete pavers while they’re damp!
- ULTRA WET LOOK® – Has your driveway or pathway taken on a dull or dry appearance? This decorative concrete sealer gives masonry pavers maximum sheen, gloss, and enhancement that lasts a long time.
- LONG-LASTING BEAUTY & VALUE – Boost the general appearance of your home! This concrete finishing solution improves the look of your patio, driveway, pool deck, and retaining wall pavers.
Out of stock
Ultra Wet Look® Concrete Paver Water Based Sealer
Ultra Wet Look® Paver Sealer From Seal ‘n Lock
Seal ‘n Lock Ultra Wet Look® paver sealer is an advanced sealer with Nano Technology, high solids, low VOC water based urethane modified acrylic for a wet look enhancement. Seal ‘n Lock Ultra-Wet-Look® paver sealer penetrates the pavers and provides a long-lasting protective barrier with excellent joint stabilization. Ultra-Wet-Look® paver sealer is formulated to seal products made to ASTM C-936 specifications and an absorption rate of 5% or less. Pavers with higher absorption rate will require additional application(s) of sealer.
Ultra Wet Look® paver sealer is user friendly and environmentally safe. The high solids content of pure urethane wears evenly and lasts longer than solvent based paver sealers.
Ultra Wet Look® paver sealer is available in 5 gallon pails.
Ultra Wet Look® paver sealer benefits
Superior Joint Stabilization
“Wet Look” Shine
Inhibits Algae & Mold Growth
All Seal ‘n Lock products are made of the most environmentally-friendly products available, and offer excellent weatherability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states, and exceeds all hardscape product manufacturers minimum standards guidelines.
Typically, the application rate will vary from 150 to 200 sq. ft. per gallon, although this rate will vary depending on the texture, absorption rate of the surface and the width of the paver joints.
DIRECTIONS FOR USE:
We recommend wearing protective goggles and latex gloves. For best results, apply Super Wet Look® paver sealer at temperatures between 60° F and 90° F. In cooler conditions, the paver sealer should be warmed to approximately 70° F. Do not apply if surface or ambient temperature s below 50°F. A test for compatibility, penetration and adhesion is recommended. If the temperature is going to drop below freezing (32° F) make sure sealer has time to cure.
Ultra Wet Look® paver sealer is designed to be diluted with 1 part water to 1 part sealer. Ultra Wet Look® paver sealer requires mixing (2 minutes) prior to use. We recommend 2 coats. Pavers with high absorption rate will require additional top coats of sealer to provide a protective barrier and desired enhancement. Ultra Wet Look® is not intended for submerged surfaces.
Ultra Wet Look® paver sealer will normally dry in sunny areas within approximately 1 hour. Shaded areas, lower temperatures or high relative humidity will slow the drying process. The surface may be open to foot traffic in 4 hours and to vehicular traffic in 48 hours. To minimize tire marks, vehicles should not make sudden stops or tight turns.
Immediately flush and agitate pump system after sealing with a mixture of 3 gallons water and 8 ounces of pine sol
Flush out the pump system with 5 gallons of fresh water – 1 gallon every 5 minutes
Always run water through the pump the next morning to have it ready for use
Pavers with high absorption rate will require additional top coats of sealer to provide a protective barrier and desired enhancement.
Ultra Wet Look® paver sealer is not intended for submerged surfaces.
Periodic washing of pavers with a mild detergent to keep the area clean is recommended.
DO NOT USE ACIDS. Gasoline, hydraulic fluids and motor oil spills should be removed from the surface of the pavers as soon as possible. We recommend that surfaces previously sealed with Super Wet Look® should be cleaned and resealed every 3 years, depending on environmental exposure and traffic.
CAUTION: Too many coats of sealer may induce a slippery condition. May be slippery during the application if walked on. May cause skin and eye irritation. Do not take internally. Wear mask. All label directions should be read thoroughly before use.
|Dimensions||12 × 12 × 16 in|