Seal ‘n Lock Super Wet Look Concrete Paver Water Based Sealer

(2 customer reviews)

$174.95$259.95

  • FINISH EVERYTHING IN 1 DAY – No need to wait for your pavers to dry before using this water based concrete sealer. You can apply the sealer on your concrete pavers while they’re damp!
  • PROTECT YOUR PAVERS – Applying this water-based sealer on your pavers will help provide added protection against fading, discoloration, tire marks, stains, algae, oil, grease and grime.
  • ENVIRONMENTALLY FRIENDLY – Apply this paver sealer without feeling guilty about harming the environment. This biodegradable sealer does not contain toxic chemicals or ozone-depleting compounds.
  • RICH & DEEP COLORS – Why settle for dull-looking decorative concrete pavers? This 2-part, high-solids concrete sealer gives paved surfaces a deep, wet, and glossy look all-year-round.
  • LONG-LASTING BEAUTY & VALUE – Boost the general appearance of your home! This concrete finishing solution improves the look of your patio, driveway, pool deck, and retaining wall pavers.
  • SUPER WET LOOK PAVER SEALER from Seal n Lock is a high solids, two-part water based pure urethane sealer that penetrates the pavers to provide a longer lasting protective barrier with superior joint stabilization (no need for polymeric sand) resulting in a ‘wet’ look.
  • SUPER WET LOOK PAVER SEALER is user friendly. The high solids content of pure urethane wears evenly and lasts longer than solvent based sealers.
  • SUPER WET LOOK PAVER SEALER is available in 2 gallon and 5 gallon kits.
Clear

Description

Seal ‘n Lock Super Wet Look Concrete Paver Water Based Sealer

Super Wet Look Paver Sealer by Seal 'n Lock

Super Wet Look® Paver Sealer from Seal n Lock is a high solids, two-part water based pure urethane sealer that penetrates the pavers to provide a longer lasting protective barrier with superior joint stabilization (no need for polymeric sand) resulting in a ‘wet’ look.

Super Wet Look® is user friendly and environmentally safe. The high solids content of pure urethane wears evenly and lasts longer than solvent based sealers.

Super Wet Look® is available in 2 gallon and 5 gallon kits.

Super Wet Look® Benefits

  • Two Part Urethane

  • Superior Joint Stabilization

  • “Wet Look” Shine

  • Inhibits Algae & Mold Growth

  • Enhances Colors

All Seal ‘n Lock products are made of the most environmentally-friendly products available, and offer excellent weatherability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states, and exceeds all hardscape product manufacturers minimum standards guidelines.

ESTIMATING GUIDE:

Typically, the application rate will vary from 150 to 200 sq. ft. per gallon, although this rate will vary depending on the texture, absorption rate of the surface and the width of the paver joints.

DIRECTIONS FOR USE:

We recommend wearing protective goggles and latex gloves. For best results, apply Super Wet Look® at temperatures between 60° F and 90° F. In cooler conditions, the sealer should be warmed to approximately 70° F. Do not apply if surface or ambient temperature s below 50°F. A test for compatibility, penetration and adhesion is recommended. If the temperature is going to drop below freezing (32° F) make sure sealer has time to cure.

MIXING:

Super Wet Look® is a 2 part urethane which comes packaged in a 2-gallon kit (3 ½ gallon pail) and a 5-gallon kit (6-gallon pail). Part B (metal container) is cradled inside of Part A (pail). Part A and Part B require mixing and stirring (2 minutes) prior to use. Super Wet paver sealer can be diluted, after mixing with up to 2 parts water and 1 part sealer and makes up to 15 gallons. After mixing, the product must be used within two (2) hours and cannot be stored for future use.

DRYING TIME:

Super Wet Look® sealer will normally dry in sunny areas within approximately 1 hour. Shaded areas, lower temperatures or high relative humidity will slow the drying process. The surface may be open to foot traffic in 4 hours and to vehicular traffic in 48 hours. To minimize tire marks, vehicles should not make sudden stops or tight turns.

CLEANUP:

  • Immediately flush and agitate pump system after sealing with a mixture of 3 gallons water and 8 ounces of pine sol

  • Flush out the pump system with 5 gallons of fresh water – 1 gallon every 5 minutes

  • Always run water through the pump the next morning to have it ready for use

  • View Seal ‘n Lock Pail Pump Cleanout Instructions

NOTES:

  • Pavers with high absorption rate will require additional top coats of sealer to provide a protective barrier and desired enhancement.

  • Super Wet Look® is not intended for submerged surfaces.

MAINTENANCE:

Periodic washing of pavers with a mild detergent to keep the area clean is recommended.

DO NOT USE ACIDSGasoline, hydraulic fluids and motor oil spills should be removed from the surface of the pavers as soon as possible. We recommend that surfaces previously sealed with Super Wet Look® should be cleaned and resealed every 3 years, depending on environmental exposure and traffic.

CAUTION: Too many coats of sealer may induce a slippery condition. May be slippery during the application if walked on. May cause skin and eye irritation. Do not take internally. Wear mask. All label directions should be read thoroughly before use.

Additional information

Weight44 lbs
Dimensions12 × 12 × 16 in
Size

2 Gallon Kit, 5 Gallon Kit

2 reviews for Seal ‘n Lock Super Wet Look Concrete Paver Water Based Sealer

  1. John F.

    Been using Seal n Lock for several years now and would never use any other products! Excellent application results, easy to use and the best support system in the business by a mile!

    Every product from the company exceeds expectations and gives us the confidence when pricing jobs that the results will be superb!

    As a company that does not advertise but gets most of its work from referrals we need to use the best products available and Seal N Lock without question is the best sealer we have ever used.

  2. Brandyn

    Seal n’ Lock is Seal Florida South’s preferred method to seal pavers in South Florida. The products they offfer are hands down the best on the market and simple to apply. We have yet to have an unsatisfied customer. Thank you to Seal n’ Lock for the eat sealer in the industry and the best support in the business. Thank you Scott, Rich and Mary.

Add a review

Your email address will not be published. Required fields are marked *